[Resolved] Belt not tightening, just slips

Chris I had one of my 3 belts slip a bit too but I came up with an easy fix you might have luck with. I cut a thin piece of duct tape like maybe 1/2" wide and 2" long and I wrapped the tape around the belt right next to the metal clips. It worked flawlessly, give it a try. Your probably right about the oil or maybe even some dust/oil from you hands. Be sure the belts are super clean, maybe clean the end with some alcohol too. Cheers, stay positive, it will be worth it!

Another fix would be to just put a tiny 1/2" extra piece of belt under the clip to provide a tighter grip. Good luck!

Hi Chris,

If you’re still having trouble with the belts slipping, another thing you can do is put zip ties around the belt like this (make sure it points away from the v-wheel):

My plan of attack for today is to clean the belts (and all extrusions) with some 99% isopropyl alcohol to remove any potential rogue oil, then try tightening the belt again.

I almost wonder if using some CA glue on the belt ends would solve the slipping issue without adding potential complications in the future.

That would likely work great. I just don’t want duct tape on a brand new machine. :wink:

Some heat shrink might also work. I may give that a shot. Leaving the belt naked at that attachment point and relying on friction alone just seems like asking for trouble, especially if like my you want to cut harder materials like soft aluminum.

Hi @ChrisEllerby here’s another idea you could try. If you wrap the belt through like the diagram below you it might get more friction since the bracket would be holding it down. Can you try this approach?

I just went with heat shrink on each connection point. It holds tight, flexes, and is more or less invisible. It can even be easily removed if the belt needs further adjusting.

2 Likes

Thanks JeffTalbot. Zip-ties FTW.

This belt-clip design should be tweaked, though. :wink:

It was at this step I realized that I must have used an M5x25mm for the wrong part. :frowning:

Finally, i use betl clip form Shapeoko 2. Good deal.

I used zip ties on a couple of them, but then realized it was going to interfere with the carriage, so I replace them with a few wraps of electrical tape, and that seems to be working for now.

1 Like

@PeterJames
Thanks for this tip. I used 1/2" electrical tape and it worked wonders and is discrete.

I also used heatshrink after my belts started loosening. Works extremely well and makes tensioning much easier.

1 Like

Was having this same problem. Zip ties worked perfect! Thanks guys

1 Like

Routing the belt like below works for me.

1 Like

This was a major issue when building my X-Carve. I had to take everything back apart and add heat shrink AND zip ties to keep the belts tight, which added at least an hour to the overall build… Can we add this to the instructions to save everyone else the hassle?

3 Likes

I’ve tried all possible positions of belt and it still slips. Now if I have to add a zip tie and/or shrink etc. Then this needs to be address in the instructions not on the forum which you have to search and find solutions to how to build a product. Now if this was on an additional part /add on thats one thing but this is for the product itself. Like having to cut a allen wretch so that it fits behind the z-axis… Zach… doing a great job on responding and leading the team but do you have someone who can spend the time searching the forums and revise the instructions so that all the people new to cnc can build the x-carve without having to provide extra engineering?

1 Like

@ChristopherMay sorry you struggled with this one. We have a new design in the works that we will be rolling out.

@JohnHayes can you please add a note in the instructions to address what @christopherMay is talking about?

Also quick note that anyone can update the instructions now. You make a request and @johnhayes will review it and approve of give you feedback.

We are hosting them on github which is used as a version control system.

Thanks Zach for the quickness as usual. I still am struggling with it sweating in the shop. None of the belts will stay. If there was another hole in the bracket the belt could be double bacadn.ith a push pin and double backed through the loops using the pin as an anchor. It rest on the rail and seems to work.

Sorry the text got scrambled when I tried uploading pic. Double backed… “i improvised with a push pin…”